Weighing filling machine LA30
Product
Click image to view full sizeItem-Name:
Weighing filling machine LA30
Weighing filling machine LA30
More-Details:
| I.specification： |
- ‧ Filling volume: 2L—3.2L
- ‧ suited for filling Hairspray, solder paste, grease, silicone raw materials, etc... Or any non-flowing raw materials can be filled
- ‧ During the filling process, the bottle is lowered synchronously to avoid the accumulation of bubbles in the content
- ‧ Control system: PLC
- ‧ Machine size:L2779mm x W1303nn x H2773mm
| II.LA-30 Machine Layout |
More Products
Ink cartridge filling machine JB-30
I.Specification: ‧ Independent setting for each module. ‧ Independently set Yield achieve alarm. ‧ manually put steel balls and automatic implant. ‧ Place and remove the ink box manually. ‧ fixture according to the product ink box design. ‧ Automatic vacuum before ink filling. ‧ Use volumetric filling. ‧ Applicable Ink cartridge :by user ink cartridge. ‧ Control system: PLC+HMI ‧ Machine size:L900mmx W580nnx H高1770mm (Includes indicator light) II.JB-30 Partial configuration
Tube filling Machine AB220
I.specification： ‧ Servo-driven filling system ‧ Filling volume is set from HMI ‧ Filling capacity： 15-30 ml ‧ Tail cut according to different shape Requirements ‧ Voltage: 3-phase：380／220V；50／60HZ ‧ Air pressure: 5 bar流量130L/min ‧ Option Heating function according to filling requirements ‧ Operating system: PLC+HMI ‧ Machine size: L1200mm*W900mm*H2300mm ‧ Machine weight:650kg ‧ Operating procedures : Set Production quantity. >Replace date stamp >Start production II.Runner schematic diagram： III.Tail cut style： IV.AB220 Machine main unit name V.AB220 Work station layout
RS20 Planetary mixer
I.Introduction： 1.RS20 planetary mixer is Mingfeng Technology Co., Ltd. A new mixer developed for small-scale trial production before mass production and mass production. 2.RS20 planetary mixer including all the functions of large-scale production mixer, including Vacuum extraction/high speed molecular diffusion mixing blade/slow speed stirring/barrel cooling and heating and Blow air... 3.Adopt hydraulic drive lifting mechanism to lift the material barrel and Tightly integrated with upper frame, use double Oring installed in the tank to achieve the sealing effect, and the vacuum degree in the barrel can be maintained after vacuum.The upper and lower spaces are separated by mechanical rotating oil seals and silicone oil to prevent dust or oil contamination on the upper transmission part from contaminating the raw materials. 4.The Various operating Time setting use HMI. 5.Components in contact with raw materials use sus. 6.machine design is very precise and can be done in the shortest time accomplish Requirements for material dispersion and mixing. 7.Provide complete and simple parameter setting and multiple security detection Features. 8.Man-machine interface display parameter setting/data storage and troubleshooting guide. II.Specification： 1.Applicable compounds : chemical or non-chemical pasty 2.Applicable viscosity : Below 300,000CPS 3.Capacity : 20 liters 4.mixing shafts : 3 5.Voltage : 3-PHASE;415/380/220V;50/60HZ 6.Power : 6.5KW 7.Air : 5.0 bar ,30L/min 8.Cooling water : 200C 2KG/CM2;20 liter/min. 9.Material : Mixing drum SUS304, Shaft and stirring bladeSUS304(SUS303) 10.Control system: HMI+ PLC program control 11.Equipment size :1350(L)1000(W)2150(H) 12.Weight : Net weight is about 1300KG III.Name of main parts of the machine：
Mix Machinery MIX-A00
Colloidal Material Mixer Product specifications according to customer demand
Hydraulic Measure Control M/C HC-100
Hydraulic Measure Control System Product specifications according to customer demand
Semi Automatic Filling Machine SFL-A06
Main PARTS: 1.SILICONE PASTE PUSH OUT MACHINE BY HYDRAULIC SYSTEM.2.FILLING MACHINE MACHINE SIZE: HYDRAULIC PUSH OUT MACHINE : LENGTH:1.2M WIDTH:1.5M HIGH:3.0M.FILLING MACHINE: LENGTH:2.3M WIDTH:1M HIGH:1.83M. MASTER FUNCTION: MAX PRESSURE:35TONSFILLING RECYCLING CAPACITY PROBABLY:18~26 PCS/MIN.FILLING VOLUME TOLERANCE ±0.5％. MAIN EQUIPMENT: HYDRAULIC SYSTEM FOR SILICONE PUSH OUT MACHINE: MAX PRESSURE ABILITY 35TONS. HYDRAULIC MOTOR:7.5HP OIL PRESSURE 140KG/CM2. HYDRAULIC OIL:#68 COOLING SYSTEM TO CONTROL OIL TEMPERARURE. OIL TEMPERATURE MUST KEEP BELOW 50℃. CYLINDER DIAMETER 180Ø,LENGTH 1100MM MAX PRESSURE 140KG/CM2. THE CIRCLE PALLET OF SILICONE PRESSURE HAVE TWO O TYPE RING WHICH MADE BYRUBBER.DO NOT USE SHARP-POINTED TOOLS OR FIRE TO CLEAN. THE SILICONE TUBE CLIP-ON HOLDER MUST OPERATOR OTHERWISE. THE HYDRAULIC CYLINDER AXLE CENTER WILL BE DESTROY. THE O TYPE RING. WHICH MAKE FROM FINESIL TECHNOLOGY, EACH ONE. FILLING MACHINE DEVICE: CARTRIDGE PLACE SHELF 1.FILLING CUTTING SYSTEM 2.PLUNGER SUPPLY SYSTEM 3.PLUNGER PUSH UNIT 4.CARTRIDGE MOVING UNIT 5. PRINTING UNI TRINTING UNIT 6.VOLUME MEASUREMENT UNIT 7.FILLING NOZZLE PARTS and STUFF BASE 8.CONTROL SYSTEM 9.PRINTER (OPTION) FILLING CUTTING SYSTEM Manually place the empty tube to the empty tube support seat, press the start button to stat automatically filling. Will automatically cut and return after filling, the mode is the same as the automatic filling machine PLUNGER SUPPLY SYSTEM PLUNGER SUPPLY SYSTEM DIVIDE THREE PARTS: 1.PLUNGER STORAGE TANK & CONVEYOR 2.PLUNGER BUFFER SLIDE 3.PLUNGER FIRM MOLD (1)PLUNGER STORE TANK & CONVEYOR: PLUNGER STORE TANK CAPACITY:500 PIECE(2)PLUNGER BUFFER SLIDE:BUFFER SLIDE MADE BY STAINLESS STEEL HERE ARE SOME WOOL INSIDE TO ABSORB OIL AND ABOUT 20 PIECE BUFFER (3)PLUNGER SUPPORT MOLD: PLUNGER SUPPORT MOLD BY INCOOPERATE INTO ASSEMBLY PLUNGER PUSH UNIT MAIN PARTS:PUSH CYLINDER(FESTO 63Ø*200MM) PLUNGER CLIP CYLINDER (FESTO 12Ø*10MM) PLUNGER OK/NG DETECT CYLINDER (FESTO 8Ø*80MM) THE AIR BUBBLE OF INSIDE CARTRIDGE CAUSE OF AIR PRESSURE SO MUST ADJUST SUITABLE.THE FUNCTION OF PLUNGER OK/NG DETECT CYLINDER IS TO CHECK SOME ERROR OF PLUNGER.IF THERE ARE SOME TROUBLE HAPPEN IT WILL SHOW ON TOUCH SCREEN & THE MACHINE STOP. Cartridge Moving Unit When the plunger pushing action is completed, the horizontal movement mechanism automatically moves the finished product to the printing position, and pushes the finished product to the slide, so that the finished product slides into the prepared finished product box. SILICONE MEASURE UNIT DIVIDE TWO PARTS: 1.MEASURE TANK 2.THREE WAY VALVE (1)MEASURE TANK: HYDRAULIC CYLINDER 63Ø*200MM IS THE MAIN PUSH POWER.SCREW NUT ABOVE HYDRAULIC CYLINDER CAN ADJUST SILICONEVOLUME.SURE-TANK100ØDIAMETER AND PISTONE ARE TING CHROMIUM.TTENITON TO INSIDE EASURE-TANK.KEEP CONE OIL ON FULL TO AVOID PISTON & MEASURE-TANK TORY. (2)THREE WAY VALVE: THERE IS A COPPER AXLE CENTER INSDE THREE WAY VALVE.DO NOT KNOCK ON IT SURFACE OTHERWISE IT WILL LOSE EXACT TOLERANCE.THE THREE WAY VALVE INSIDE SURFACE CAN NOT TO DESTORE WHEN YOU CLEAN SILITONE.THERE ARE TWO PACKING ORING BOTH SIDES THE THREE WAY VALVE WHAT CAN AUTOSUPPLY OIL TO LUBRICATE & AVOID SILICONE TO CONGEAL. (3)THE THREE WAY VALVE IS MADE BY STAINLESS STEEL. THE FILLING NOZZLE IS MADE BY STAINLESS STEEL.THE INNER CORE IS TO CLEAN. 1.THE FILLING MACHINE CONTROL SYSTEM USE MITSUBISHI PROGRAM LANGUAGECONTROLLER(PLC) + MAN MACHINE INTERFACE(MMI). 2.THE FUNCTION OF MAN MACHINE INTERFACE(MMI): DURING PRODUCTION.IF THERE ARE SOMETHING ERROR THE PROGRAM LANGUAGE CONTROLLER (PLC)WILL STOP WHOLE SYSTEM AND SHOW ERROR MESSAGE ON MAN MACHINE INTERFACE(MMI).THE MMI CAN RECOMMEND HOW TO TROUBLE SHOOTING.OPERATOR MUST SOLVE THE PROBLUMAND THEN CONTINUE PRODUCTION. Filling Step: a.Put a cartridge on the clip b.The detector of cartridge is active and cartridge clip is active,then CARTRIDGE CYLINDER forward and nozzle inside the cartridge,also the obstructing cylinder forward. c.STUFF CYLINDER forward, then the Air exhaust from cylinder to release rear pressure,the cylinder under FREE condition. The exhaust time is adjustable, minimum 0.01 second.Once, exhaust time was over, the hydraulic COUNTING CYLINDER is active, when the glue besqueezed into cartridge, at same time, the STUFF CYLINDER be push back.After stuff action was completed, a limit switch will be active, means stuff over. d.STUFF TIME is adjustable, to completely squeeze the glue. Once time out,the stuff cylinder will turn back to stand-by position. At same time, CUTTER CLUTCH active,once cut time was over, both STUFF CYLINDER and OBSTUCTING CYLINDER will turn back to stand-by position.STUFF CLIP open. e.3-way valve start to active and re-fill the glue,thus COUNTING CYLINDER turn back to stand-by position. f.When the filling step finished, taking the cartridge to Plunger Station g.The action of Stuff and Plunger is operated at same time.Once the cartridge was detected atPlunger Station, the PLUNGER CYLINDER will be active and insert the plunger into the cartridge.When PLUNGER CYLINDER forward to set position,will idle a while(adjustable),then PLUNGER CYLINDERturn back to stand-by position.There is a detector at front of PLUNGER CYLINDER,if active which meanssilicone quantity shorted. h.After plunger, operation conveyor moves again to next step for printing. Once the cartridge was detectedat Print Station, print cylinder will forward and (cartridge rotate) motor active, fix plate push down andholding the cartridge, then JET PRINTER active. The operation time of printer will be set by PLC.After time out,print cylinder turn back to stand-by position, motor stop.i.operation conveyor moves again to next step. Finally, the cartridge (finished product)will be rolling to package table.Red word section describes is manual operation
Silicone Filling Machine SL-A06
Silicone Filling System I.MAIN PARTS A.Hydraulic Silicone Push Out MachineB.Filling MachineProduction direction from left to right Production direction from right to left II.Hydraulic Silicone Push Out Machine A.1.2M * 1.5M * 3.0M (Length, Width, High)B.Filling Machine: 4M * 2M * 2.5M (Length, Width, High) III.MAIN FUNCTION A.Max Pressure: 35TB.Filling Speed: 25~30 pcs/minC.Filling Volume Tolerance: ±0.5％ IV.MAIN EQUIPMENT A.Hydraulic Silicone Push Out Machine 1.Max pressure capacity: 35 Tons2.Hydraulic motor : 7.5HP , max oil pressure 140 kg/cm23.Hydraulic oil: #684.Using water-cooling pipe attached unit to cool down the hydraulic oil temperature.5.Keep the hydraulic oil temperature below 50℃6.Cylinder diameter 180ψ,length 1100mm , max pressure 140kg/cm27.The circle pallet has two o-ring, which made of rubber. Please keep it away from sharp-pointed tool or fire.8.The fix tube folder must be operated according to the standard, in order to avoid the axle of hydraulic cylinder from being hurt.9.The o-ring is manufactured with model by Ming Feng.10.The heavy type 60ψtube conveyer (option), length 2m,width 0.65m. B.Filling Machine 1.Cartridge Supply Conveyer 2.Plunger Supply Conveyer 3.Horizontal Moving Unit 4.Filling / Deliver Cartridge System 5.Plunger Push Unit 6.Pressure Measurement Unit 7.Filling Nozzle Parts 8.Printer (option) 9.Printer Roller Unit (option) 1. Cartridge Supply Conveyer Cartridge Supply System Divide In Two Parts: (1.) Cartridge Storage Tank:Tank made by stainless steel#304, thickness 1.5mm, capacity 700pcs. (2.) Cartridge Take Up Conveyer:Take up conveyer composed by stainless steel flat chain with 90w speed control motor, capacity 50pcs/min. 2. Plunger Supply System Plunger Supply System Divide In Three Parts: (1.) Plunger Storage Tank:Tank made by stainless steel#304, thickness 1.5mm, capacity 3000pcs. (2.) Plunger Filter Conveyer:Filter conveyer chain made by stainless steel. Fuselage is cover with 2mm stainless steel. Capacity 38pcs/min. (3.) Cartridge Slide Chute:The chute is made by stainless steel, covered with oil absorption wool, capacity 30 plungers. 3. Horizontal Moving Unit Horizontal Moving Unit use # 2060R special chain, can transport 100times/min. Using separator to locate the position. Locating fast and accurately, as the improved model of displacement. 4. Filling / Deliver Cartridge System Main Parts: (1.)FESTO Cylinder (25ψ*240mm)MMain Parts:(2.)FESTO Locate Position CylinderThe time and speed of cutting is the key to the silicone cutting perfectly or not. Although this machine is fully automatic, the operator must be aware of the coordination between both speed and time. 5. Plunger Push Unit Main Parts: (1.)Plunger Push Cylinder (FESTO 63ψ*200mm)Main Parts: (2.)Plunger Clip Cylinder (FESTO 12ψ*10mm)Main Parts: (3.)Plunger Detect Cylinder (FESTO 8ψ*80mm) The pressure of pushing plunger are tidily connect with the result if any air bubble remains in the cartridge. The plunger push cylinder is capable with a regulators, to adjust the pressure to an appropriate limit.The plunger detect cylinder is to detect the plunger push process function well, if not, it will alert and the machine will stop. 6. Pressure Measurement Unit Pressure Measurement Unit Divide In Two Parts: (1.) Hydraulic Measure BarrelUsing 63ψhydraulic cylinder for thrusting, screw nut above the hydraulic cylinder is used to adjust the volume. The barrel is ψ100, chromium plating surface. The piston’s surface is covered with chromium plating also. Please keep the silicone oil within the piston remain, in order to cut down the wear and tear. (2.) Three way valve: Three way valve is made of stainless steel. Please be careful with the copper axis inside the three way valve. It must not be tap to protect the surface, so as not to damage the precision. 7. Filling Nozzle Parts: The Filling Nozzle Parts Divide In Two Parts: (1.) Inner Core:The core is made of stainless steel, connected with three way valve and empty cartridge. The inner core is stationary, only remove to wash when changing color. The smoothness of inner core is important to the process of pushing the silicone into the cartridge. Please make sure removing the residue silicone entirely when cleaning. (2.) Outer Core:The outer core is made of stainless steel. In charge of cutting the silicone. The size of outer core is smaller than inner core. Driving by clutch-brake motor, it will spin very fast , and the tube screw will reverse in another way. (3.) Cutting Power GroupThe cutting power group is composed of a 1/2 HP motor, a set of timing pulley and a break clutch. The motor keep running , when the clutch run, can reach high speed cutting immediately. V.CONTROL SYSTEM A.The Program Language Controller (PLC) Control Whole Production Process.B.The Function of Man Machine Interface (MMI): 1.Parameter Modification2.Manual & Semi-Auto3.Showing Error Massage4.Showing the Method of Trouble ShootingC.Auto Detect Function1.Mistake Direction of Cartridge2.Cartridge Shortage3.Silicone Filling Shortage4.Plunger Shortage5.Mistake Direction of Plunger6.Located Position Error7.Exit Crowed *When the error above accrue, the Program Language Controller (PLC) will stop all system and show error message on the Man Machine Interface (MMI) with recommendation of trouble shooting. The machine will only re-operate when the problem has been solve.
Vacum Filling Machine
